Read online or download PDF. Page 2 / 6. Remy 28SI™ ALTERNATOR User Manual. Remy Generators Manuals Directory ManualsDir.com - online owner manuals library Search.
Alternator Assembly Delco Remy 40Si 8600390. Remote Control & Panel Manual Switch Dual Mode Operation The LCD panel with USB drive&TF card DVR and audio Mic. Only licensed Remy International, Inc. Product and component parts should be used, and the use of other parts or modifications not approved. By Remy International, Inc. Will void all applicable warranties. The failure to carefully follow these Installation Instructions, set forth above, will void all applicable warranties. DELCO REMY is a.
Advertising
Instruction Sheet
10524210
22AU13 C/P30502 REV4
NOTICE
- Only licensed Remy International, Inc. product and component parts should be used, and the use of other parts or modifications not approved
User guide. Read online or download PDF. Remy 28SI™ ALTERNATOR User Manual. Remy Generators. ANY INSTALLATION AND OR REPAIRS TO THE DELCO REMY. The 40SI design features bearings with enhanced steel and seals that improve the overall durability and life cycle of the alternator. UNIQUE STATOR DESIGN. The patented design of Delco Remy’s hairpin stator technology provides not only a high power output and maximum torque but reduced energy loss that results in best-in-class efficiency. Delco Remy alternators mean premium quality, increased efficiency, and measurable fuel savings for the commercial and off-road vehicle industry worldwide. Delco Remy starters have continuosly brought the power, outperforming the rest of the competition by as a much as 30 percent.
by Remy International, Inc. will void all applicable warranties. The failure to carefully follow these Installation Instructions, set forth above, will void all
applicable warranties. DELCO REMY is a registered trademark of General Motors Corporation, licensed to Remy International, Inc. Pendleton, IN 46064.
©
applicable warranties. DELCO REMY is a registered trademark of General Motors Corporation, licensed to Remy International, Inc. Pendleton, IN 46064.
©
2012 Remy International, Inc. All rights reserved
1
10524210
Swann security dvr 4 channel. GROUND SCREW (-)
(Two Locations)
5.6-6.8 Nm (50-60 lb in)
24SI
™ & 28SI™ ALTERNATOR INSTALLATION INSTRUCTIONS
Note: Instructions for 24SI & 28SI toreplace 21SI, 22SI
& 24SI alternators are onthe www.delcoremy.com web site.
WARNING!!!!
ALWAYS USE PROPER EYE PROTECTION WHEN PERFORMING ANY MECHANICAL REPAIRS TO A VEHICLE
- INCLUDING, BUT NOT LIMITED TO, ANY INSTALLATION AND OR REPAIRS TO THE DELCO REMY
®
ALTERNATORS. FAILURE
TO USE PROPER EYE PROTECTION CAN LEAD TO SERIOUS AND PERMANENT EYE DAMAGE.
Only perform the mechanical functions that you are properly qualified to perform. Mechanical repairs that are beyond your technical
capabilities should be handled by a professional installation specialist.
capabilities should be handled by a professional installation specialist.
DANGER!!!
To avoid injury or damage, always disconnect the negative cable at the battery before removing or replacing the alternator.
The alternator output terminal is always live (“hot”). If the battery is not disconnected, a tool accidentally touching this terminal and
ground can quickly get hot enough to burn skin or damage tools and surrounding parts.
ground can quickly get hot enough to burn skin or damage tools and surrounding parts.
NOTICE!
Some of these are extremely high output Alternators. Always ensure your application is equipped with the appropriate
size and gauge cable. CHARGING LINE CABLE VOLTAGE DROP SHOULD NOT EXCEED 0.5 VOLTS (12V system), 1.0 Volts
(24V system) (ALTERNATOR OUTPUT [B+] TERMINAL TO BATTERY POSITIVE TERMINAL AT FULL OUTPUT). FOR
OBTAINING ADDITIONAL WIRING INSTALLATION INFORMATION, SEE HEAVY DUTY APPLICATION MANUALS OR
CONTACT A REMY INC. REPRESENTATIVE.
(24V system) (ALTERNATOR OUTPUT [B+] TERMINAL TO BATTERY POSITIVE TERMINAL AT FULL OUTPUT). FOR
OBTAINING ADDITIONAL WIRING INSTALLATION INFORMATION, SEE HEAVY DUTY APPLICATION MANUALS OR
CONTACT A REMY INC. REPRESENTATIVE.
FOLLOW ENGINE OR VEHICLE MANUFACTURER’S INSTRUCTIONS FOR REMOVING THE OLD ALTERNATOR FROM THE
ENGINE AND INSTALLING THE NEW ALTERNATOR.
REMOVAL & INSTALLATION INSTRUCTIONS
Disconnect the negative (-) cable at the batteries.
Identify and tag all leads when removing the old alternator and install them on the same terminals of the new alternator.
Insure all leads are reconnected or contained where they cannot ground.
Torque all fasteners to values labeled in Figures 1, 2 & 3
This alternator may have more terminals than the one being replaced had or used. It will charge properly with only the battery and
ground leads connected. Use of the other terminals is optional based on need. See “TERMINAL DESCRIPTIONS”, Pages 2 and 3.
FIGURE 1: 28SI ALTERNATOR TORQUE VALUES
HIGH OUTPUT FEATURES
24SI:
12 Volt
– 100, 130, 145, 160 24 Volt–70, 100Ampere Ratings Connections: Three options
Mounting Options: Pad & standard Delco Remy
®
Hinge 198mm (7.8 inch)
28SI:
12 Volt
– 130, 145, 160, 180, 200 24 Volt–100Ampere Ratings Connections: Three options
Mounting Options:
Pad, & Delco Remy
®
Standard Hinge 198mm (7.8
”) & Long Hinge 216mm (8.5 inch)
24SI & 28SI: Remote Sense
™ Technology is available&Battery Isolator Bulletin is available
Battery (+)
9.0-11.3 Nm
(80 - 100 lb in)
REMOTE SENSE
™
(OPTIONAL)
INDICATOR/IGNITION
RELAY (OPTIONAL)
(3 terminals)
Delco Remy 40si Alternator User Manual Instructions
1.7
–2.8 Nm (15-25 lb in)
Standard198 mm
(7.8”)
or
28SI only - Long
216 mm (8.5”)
28SI
IS AVAILABLE IN DELCO REMY
STANDARD HINGE & LONG HINGE
MOUNTING SIZES
MOUNTING SIZES
NOTICE!
DO NOT INSTALL
AN EXTERNAL FAN ON A
24SI or 28SI ALTERNATOR
24SI or 28SI ALTERNATOR
Ground
point
USE PULLEY FROM OLD ALTERNATOR
(SEE PULLEY INSTRUCTIONS, page 2)
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals
Advertising
NOTICE
- Only licensed Remy International, Inc. product and component parts should be used, and the use of other parts or modifications not approved
by Remy International, Inc. will void all applicable warranties. The failure to carefully follow these Installation Instructions, set forth above, will void all
applicable warranties. DELCO REMY is a registered trademark of General Motors Corporation, licensed to Remy International, Inc. Pendleton, IN 46064.
©
applicable warranties. DELCO REMY is a registered trademark of General Motors Corporation, licensed to Remy International, Inc. Pendleton, IN 46064.
©
2012 Remy International, Inc. All rights reserved
2
10524210
PHASE (RELAY)
INDICATOR LAMP
EXTERNAL FIELD MONITOR
REMOTE SENSE
(OPTIONAL)
REMOTE SENSE
(OPTIONAL)
GROUND SCREW (-)
5.6-6.8 Nm (50-60 lb in)
PULLEY INSTRUCTIONS: Use pulley from old alternator if this alternator does not have one or pulley supplied is different from pulley
on alternator being replaced. NOTICE! When changing the pulley, keep the alternator shaft in the horizontal position and do not
apply any pressure to end of the shaft. Internal damage may occur if the shaft is pushed back and turned.All alternators are
shipped with spacers that go behind the pulley. During installation of the pulley, assure these parts are in the same order as
received. If the old alternator has different spacers, use them and Install on this alternator in same order as removed. Assure the
pulley turns freely prior to installation.
Hold the shaft by placing a hex wrench in the hexagonal hole in the shaft while removing or installing the pulley. Tighten the pulley nut
to 95-108 Nm (70-80 lb ft). Do not install the fan.
BELT TENSIONING INSTRUCTIONS: Improper belt tension can cause premature alternator failure. If the belt must
be tightened manually, place a wood block between the alternator and pry bar, as illustrated at right. Pry as close to
the center of the unit as possible. Use a torque wrench to tighten mounting bolts to the proper torque as specified in
vehicle or engine manufacturer’s specifications for belt tension and mounting bolts torque. DO NOT OVER TIGHTEN
BELT!
apply any pressure to end of the shaft. Internal damage may occur if the shaft is pushed back and turned.All alternators are
shipped with spacers that go behind the pulley. During installation of the pulley, assure these parts are in the same order as
received. If the old alternator has different spacers, use them and Install on this alternator in same order as removed. Assure the
pulley turns freely prior to installation.
Hold the shaft by placing a hex wrench in the hexagonal hole in the shaft while removing or installing the pulley. Tighten the pulley nut
to 95-108 Nm (70-80 lb ft). Do not install the fan.
BELT TENSIONING INSTRUCTIONS: Improper belt tension can cause premature alternator failure. If the belt must
be tightened manually, place a wood block between the alternator and pry bar, as illustrated at right. Pry as close to
the center of the unit as possible. Use a torque wrench to tighten mounting bolts to the proper torque as specified in
vehicle or engine manufacturer’s specifications for belt tension and mounting bolts torque. DO NOT OVER TIGHTEN
BELT!
FIGURE 4: TYPICAL WIRING DIAGRAM
FOR STUD CONNECTORS
TERMINAL DESCRIPTIONS (Alternator will function without connecting the S, I or R terminals):
“B+” Terminal -Output terminal connects to the positive (+) battery terminal.
“S” Remote Sense™ Terminal – Connect to system voltage at the battery or a common distribution point.
“R” Terminal – Relay / Phase terminal carries half system voltage and may be used for certain types of control relays, charge
indicators, tachometers or similar devices. The current draw should not exceed four (4) amperes. Frequency = Alternator RPM/10.
Notice!
The “R” Terminal is not the Remote Sense™ terminal – do not connect to B+!
“I” Terminal - The Indicator lamp/ignition terminal can serve as a current source, sink or both, depending on how it is connected. The
diagram above shows one configuration. Current capability is 1.0 Amp in either direction.
diagram above shows one configuration. Current capability is 1.0 Amp in either direction.
Ground Screw
– Ground lead ensures alternator is grounded and is strongly recommended for optimum performance.
RELAY TERMINAL OUTPUT IS
AT 1/2 SYSTEM VOLTAGE
AT 1/2 SYSTEM VOLTAGE
USE PULLEY FROM OLD ALTERNATOR
(SEE PULLEY INSTRUCTIONS PAGE 2
NOTICE!
DO NOT INSTALL AN EXTERNAL
FAN ON A 24SI OR 28SI
ALTERNATOR
FIGURE 3 - 24SI & 28SI (STUD TERIMINALS)
FIGURE 2: 24SI & 28SI (4-PIN PLUG TERMINALS)
REMOTE SENSE
(
OPTIONAL
)
INDICATOR/IGNITION
RELAY (Optional pin terminal)
Three (3) M5 terminals torque
3.0
–5.0 Nm (27-44 lb in)
Three (3) #10 terminals torque
1.7
1.7
–2.8 Nm (15-25 lb in)
RELAY PIN TERMINAL CONNECTOR - OBTAIN
FROM DELPHI OR OTHER APPROVED SOURCE
FROM DELPHI OR OTHER APPROVED SOURCE
BATTERY (+)
9.0-13.0 Nm
(80-120 lb in)
9.0-13.0 Nm
(80-120 lb in)
BATTERY (+)
9.0-13.0 Nm
(80-120 lb in)
GROUND SCREW (-)
5.6-6.8 Nm (50-60 lb in)
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals